| range of product |
Altivar 12 |
|
|---|---|---|
| product or component type |
Variable speed drive |
|
| product destination |
Asynchronous motors |
|
| product specific application |
Simple machine |
|
| assembly style |
With heat sink |
|
| component name |
ATV12 |
|
| quantity per set |
Set of 1 |
|
| EMC filter |
Integrated |
|
| built-in fan |
With |
|
| network number of phases |
1 phase |
|
| [Us] rated supply voltage |
200…240 V – 15…10 % |
|
| motor power kW |
2.2 kW |
|
| motor power hp |
3 hp |
|
| communication port protocol |
Modbus |
|
| line current |
24 A at 200 V 20.2 A at 240 V |
|
| speed range |
1…20 |
|
| transient overtorque |
150…170 % of nominal motor torque depending on drive rating and type of motor |
|
| asynchronous motor control profile |
Sensorless flux vector control Quadratic voltage/frequency ratio Voltage/frequency ratio (V/f) |
|
| IP degree of protection |
IP20 without blanking plate on upper part |
|
| noise level |
45 dB |
| supply frequency |
50/60 Hz +/- 5 % |
|
|---|---|---|
| connector type |
1 RJ45 (on front face) for Modbus |
|
| physical interface |
2-wire RS 485 for Modbus |
|
| transmission frame |
RTU for Modbus |
|
| transmission rate |
4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s |
|
| number of addresses |
1…247 for Modbus |
|
| communication service |
Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43) |
|
| prospective line Isc |
1 kA |
|
| continuous output current |
10 A at 4 kHz |
|
| maximum transient current |
15 A for 60 s |
|
| speed drive output frequency |
0.5…400 Hz |
|
| nominal switching frequency |
4 kHz |
|
| switching frequency |
2…16 kHz adjustable 4…16 kHz with derating factor |
|
| braking torque |
Up to 70 % of nominal motor torque without braking resistor |
|
| motor slip compensation |
Adjustable Preset in factory |
|
| output voltage |
200…240 V 3 phases |
|
| electrical connection |
Terminal, clamping capacity: 5.5 mm², AWG 10 (L1, L2, L3, U, V, W, PA, PC) |
|
| tightening torque |
1.2 N.m |
|
| insulation |
Electrical between power and control |
|
| supply |
Internal supply for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protection Internal supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection |
|
| analogue input number |
1 |
|
| analogue input type |
Configurable current AI1 0…20 mA 250 Ohm Configurable voltage AI1 0…10 V 30 kOhm Configurable voltage AI1 0…5 V 30 kOhm |
|
| discrete input number |
4 |
|
| discrete input type |
Programmable LI1…LI4 24 V 18…30 V |
|
| discrete input logic |
Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm Positive logic (source), 0…< 5 V (state 0), > 11 V (state 1) |
|
| sampling duration |
20 ms, tolerance +/- 1 ms for logic input 10 ms for analogue input |
|
| linearity error |
+/- 0.3 % of maximum value for analogue input |
|
| analogue output number |
1 |
|
| analogue output type |
AO1 software-configurable voltage: 0…10 V, impedance: 470 Ohm, resolution 8 bits AO1 software-configurable current: 0…20 mA, impedance: 800 Ohm, resolution 8 bits |
|
| discrete output number |
2 |
|
| discrete output type |
Logic output LO+, LO- Protected relay output R1A, R1B, R1C 1 C/O |
|
| minimum switching current |
5 mA at 24 V DC for logic relay |
|
| maximum switching current |
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay |
|
| acceleration and deceleration ramps |
Linear from 0 to 999.9 s U S |
|
| braking to standstill |
By DC injection, <30 s |
|
| protection type |
Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Against input phase loss in three-phase Thermal motor protection via the drive by continuous calculation of I²t |
|
| frequency resolution |
Analog input: converter A/D, 10 bits Display unit: 0.1 Hz |
|
| time constant |
20 ms +/- 1 ms for reference change |
|
| marking |
CE |
|
| operating position |
Vertical +/- 10 degree |
|
| height |
142 mm |
|
| width |
105 mm |
|
| depth |
156.2 mm |
|
| net weight |
1.4 kg |
|
| functionality |
Basic |
|
| specific application |
Commercial equipment |
|
| Variable speed drive application selection |
Commercial equipment Mixer Commercial equipment Other application Textile Ironing |
|
| motor starter type |
Variable speed drive |
| electromagnetic compatibility |
Electrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4 Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2 Immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6 Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3 Surge immunity test level 3 conforming to EN/IEC 61000-4-5 Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11 |
|
|---|---|---|
| electromagnetic emission |
Radiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2…16 kHz shielded motor cable Conducted emissions with integrated EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <5 m Conducted emissions with additional EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 4…12 kHz shielded motor cable <20 m Conducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4…12 kHz shielded motor cable <50 m Conducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC 61800-3 4…12 kHz shielded motor cable <50 m Conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4…16 kHz shielded motor cable <5 m Conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <10 m |
|
| product certifications |
C-Tick CSA NOM UL GOST |
|
| vibration resistance |
1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-6 1.5 mm peak to peak (f = 3…13 Hz) – drive unmounted on symmetrical DIN rail – conforming to EN/IEC 60068-2-6 |
|
| shock resistance |
15 gn conforming to EN/IEC 60068-2-27 for 11 ms |
|
| relative humidity |
5…95 % without condensation conforming to IEC 60068-2-3 5…95 % without dripping water conforming to IEC 60068-2-3 |
|
| ambient air temperature for storage |
-25…70 °C |
|
| ambient air temperature for operation |
-10…50 °C protective cover from the top of the drive removed 50…60 °C with current derating 2.2 % per °C |
|
| operating altitude |
> 1000…2000 m with current derating 1 % per 100 m <= 1000 m without derating |
| Unit Type of Package 1 |
PCE |
|
|---|---|---|
| Number of Units in Package 1 |
1 |
|
| Package 1 Weight |
1.753 kg |
|
| Package 1 Height |
20 cm |
|
| Package 1 width |
18 cm |
|
| Package 1 Length |
20 cm |
|
| Package 2 Weight |
4.04 kg |
|
| Package 3 Weight |
65.95 kg |
| Sustainable offer status |
Green Premium product |
|
|---|---|---|
| REACh Regulation |
REACh Declaration |
|
| EU RoHS Directive |
Pro-active compliance (Product out of EU RoHS legal scope) EU RoHS Declaration |
|
| Mercury free |
Yes |
|
| RoHS exemption information |
Yes |
|
| China RoHS Regulation |
China RoHS declaration |
|
| Environmental Disclosure |
Product Environmental Profile |
|
| Circularity Profile |
End of Life Information |
|
| WEEE |
The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins |
| Warranty |
18 months |
|---|
There are no reviews yet.