,

ATV12H075M2

Schneider Electric

Variable speed drive ATV12 –

0.75kW – 1hp – 200..240V – 1ph – with heat sink

 

 

Compare
Main
range of product
Altivar 12
product or component type
Variable speed drive
product destination
Asynchronous motors
product specific application
Simple machine
assembly style
With heat sink
component name
ATV12
quantity per set
Set of 1
EMC filter
Integrated
built-in fan
Without
network number of phases
1 phase
[Us] rated supply voltage
200…240 V – 15…10 %
motor power kW
0.75 kW
motor power hp
1 hp
communication port protocol
Modbus
line current
10.2 A at 200 V
8.5 A at 240 V
speed range
1…20
transient overtorque
150…170 % of nominal motor torque depending on drive rating and type of motor
asynchronous motor control profile
Quadratic voltage/frequency ratio
Voltage/frequency ratio (V/f)
Sensorless flux vector control
IP degree of protection
IP20 without blanking plate on upper part
noise level
0 dB
Complementary
supply frequency
50/60 Hz +/- 5 %
connector type
1 RJ45 (on front face) for Modbus
physical interface
2-wire RS 485 for Modbus
transmission frame
RTU for Modbus
transmission rate
4800 bit/s
9600 bit/s
19200 bit/s
38400 bit/s
number of addresses
1…247 for Modbus
communication service
Read holding registers (03) 29 words
Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)
prospective line Isc
1 kA
continuous output current
4.2 A at 4 kHz
maximum transient current
6.3 A for 60 s
speed drive output frequency
0.5…400 Hz
nominal switching frequency
4 kHz
switching frequency
2…16 kHz adjustable
4…16 kHz with derating factor
braking torque
Up to 70 % of nominal motor torque without braking resistor
motor slip compensation
Preset in factory
Adjustable
output voltage
200…240 V 3 phases
electrical connection
Terminal, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC)
tightening torque
0.8 N.m
insulation
Electrical between power and control
supply
Internal supply for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protection
Internal supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection
analogue input number
1
analogue input type
Configurable current AI1 0…20 mA 250 Ohm
Configurable voltage AI1 0…10 V 30 kOhm
Configurable voltage AI1 0…5 V 30 kOhm
discrete input number
4
discrete input type
Programmable LI1…LI4 24 V 18…30 V
discrete input logic
Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm
Positive logic (source), 0…< 5 V (state 0), > 11 V (state 1)
sampling duration
20 ms, tolerance +/- 1 ms for logic input
10 ms for analogue input
linearity error
+/- 0.3 % of maximum value for analogue input
analogue output number
1
analogue output type
AO1 software-configurable voltage: 0…10 V, impedance: 470 Ohm, resolution 8 bits
AO1 software-configurable current: 0…20 mA, impedance: 800 Ohm, resolution 8 bits
discrete output number
2
discrete output type
Logic output LO+, LO-
Protected relay output R1A, R1B, R1C 1 C/O
minimum switching current
5 mA at 24 V DC for logic relay
maximum switching current
2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay
2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
acceleration and deceleration ramps
Linear from 0 to 999.9 s
U
S
braking to standstill
By DC injection, <30 s
protection type
Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
Against input phase loss in three-phase
Thermal motor protection via the drive by continuous calculation of I²t
frequency resolution
Analog input: converter A/D, 10 bits
Display unit: 0.1 Hz
time constant
20 ms +/- 1 ms for reference change
marking
CE
operating position
Vertical +/- 10 degree
height
143 mm
width
72 mm
depth
131.2 mm
net weight
0.8 kg
functionality
Basic
specific application
Commercial equipment
Variable speed drive application selection
Commercial equipment Mixer
Commercial equipment Other application
Textile Ironing
motor starter type
Variable speed drive
Environment
electromagnetic compatibility
Electrical fast transient/burst immunity test level 4 conforming to EN/IEC 61000-4-4
Electrostatic discharge immunity test level 3 conforming to EN/IEC 61000-4-2
Immunity to conducted disturbances level 3 conforming to EN/IEC 61000-4-6
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to EN/IEC 61000-4-3
Surge immunity test level 3 conforming to EN/IEC 61000-4-5
Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11
electromagnetic emission
Radiated emissions environment 1 category C2 conforming to EN/IEC 61800-3 2…16 kHz shielded motor cable
Conducted emissions with integrated EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <5 m
Conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2…12 kHz shielded motor cable <5 m
Conducted emissions with integrated EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 2, 4 and 16 kHz shielded motor cable <10 m
Conducted emissions with additional EMC filter environment 1 category C1 conforming to EN/IEC 61800-3 4…12 kHz shielded motor cable <20 m
Conducted emissions with additional EMC filter environment 1 category C2 conforming to EN/IEC 61800-3 4…12 kHz shielded motor cable <50 m
Conducted emissions with additional EMC filter environment 2 category C3 conforming to EN/IEC 61800-3 4…12 kHz shielded motor cable <50 m
product certifications
NOM
UL
GOST
C-Tick
CSA
vibration resistance
1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-6
1.5 mm peak to peak (f = 3…13 Hz) – drive unmounted on symmetrical DIN rail – conforming to EN/IEC 60068-2-6
shock resistance
15 gn conforming to EN/IEC 60068-2-27 for 11 ms
relative humidity
5…95 % without condensation conforming to IEC 60068-2-3
5…95 % without dripping water conforming to IEC 60068-2-3
ambient air temperature for storage
-25…70 °C
ambient air temperature for operation
-10…40 °C protective cover from the top of the drive removed
40…60 °C with current derating 2.2 % per °C
operating altitude
> 1000…2000 m with current derating 1 % per 100 m
<= 1000 m without derating
Packing Units
Unit Type of Package 1
PCE
Number of Units in Package 1
1
Package 1 Weight
1.11 kg
Package 1 Height
11.7 cm
Package 1 width
19 cm
Package 1 Length
19.5 cm
Package 2 Weight
1.128 kg
Package 3 Weight
63.09 kg
Offer Sustainability
Sustainable offer status
Green Premium product
REACh Regulation
REACh Declaration
EU RoHS Directive
Pro-active compliance (Product out of EU RoHS legal scope)
EU RoHS Declaration
Mercury free
Yes
RoHS exemption information
Yes
China RoHS Regulation
China RoHS declaration
Environmental Disclosure
Product Environmental Profile
Circularity Profile
End of Life Information
WEEE
The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins
Contractual warranty
Warranty
18 months
Brands

Schneider Electric

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “ATV12H075M2”

There are no reviews yet.

SHOPPING CART

close